WET SOUNDS HT-1

Sale!

$499.99 $199.99

Mono marine subwoofer amplifier — 600 watts RMS x 1 at 2 ohms

Category:

Description

Features & specs

Performance
RMS Power Output (Watts x Channels) 300 x 1
Frequency Response at Rated RMS Power 20-250 Hz
THD at Rated RMS Power 0.15%
Signal to Noise Ratio 95 dB
Input Voltage N/A
Peak Power Output (Watts x Channels) N/A
Power at 2 Ohms (Watts x Channels) 600 x 1
Bridged Power (Watts x Channels) N/A
Minimum Impedance Bridged N/A
Minimum Impedance Unbridged 2
Features
Amplifier Class D
Low-Pass Crossover Frequency 50-250 Hz
Low-Pass Slope (dB/octave) 24 dB/octave
High-Pass Crossover Frequency N/A
High-Pass Slope (dB/octave) N/A
Bass Boost 0-18 dB
Bass Boost Frequency 45 Hz
Fan Cooled No
Fuse Rating 50
Speaker Level Inputs No
Preamp Outputs 1 pair
Height (inches) 2-7/8
Width (inches) 11-1/16
Depth (inches) 7-5/16

 

Features

Marine Amplifier: The Wet Sounds Hydro-Tech series amplifiers, with conformal coated PCBs, are specifically designed for marine applications. However, the amps are not waterproof, and should not be mounted where they are likely to get wet.

Mounting Feet: Using the included mounting feet adds approximately 1/2″ to the height of the amp, but allows you to hide the wiring under the chassis.

Logo: The Wet Sounds logo mounts over the status LED, on the top of the amp. It can be mounted vertically or horizontally.

End Covers: There are removable covers on both ends of the amp to help protect the controls and connections. The covers can be painted.

Note: A 3mm Allen wrench (not included) is needed to remove the covers. They must be removed during the installation.

Wired Remote: A wired remote level control is included. The remote has integrated flanges and screws are included to mount the unit under the dash. A 16-1/4′ cable is attached to connect to the amplifier.

Note: The wired remote measures approximately 1-3/4″ wide (2-1/2″ including the mounting flanges) x 1″ tall x 1-5/8″ deep (2-1/4″ including the knob and cable).

Controls

Control Panel Cover: All the controls are protected by a rubber cover to help keep them dry.

Gain: The input gain is a continuously variable rotary control; 200 mV to 5 V.

Crossover: The low pass crossover point is adjustable from 50 Hz to 250 Hz. Because the HT-1 is a subwoofer amp, the crossover is always engaged.

Phase: The output phase is switchable; 0° or 180°.

Bass Boost: The bass boost, centered at 45 Hz, is continuously variable from 0 dB (flat) to +18 dB.

Connections

Power Terminal Block: The amplifier has a power/ground terminal block that detaches from the amplifier, making it easier to connect the power and ground wires. Once the connections are made, the terminal block plugs into the amplifier. The power/ground block has set screw terminals and will accept 4 gauge wire.

Speaker Terminal Block: The speaker terminal block is also detachable from the amplifier. The speaker block has set screw terminals for two speakers (internally wired in parallel) and the remote turn-on lead; each will accept 12-16 gauge wire.

Preamp Inputs: The amplifier has one pair of RCA jack inputs.

Preamp Outputs: There is also one pair of pass-through preamp outputs, making it easy to connect another amplifier without running an extra set of RCA cables.

Remote Level Control: The included wired remote plugs into a 3.5mm mini-plug.

Note:The preamp inputs, preamp outputs, and wired remote input are extended 5″ from the amp on pigtail wires.

Fuses: The amplifier is protected by two 25-amp ATO blade-type fuses. Marine amp Marine amp

0
search previous next tag category expand menu location phone mail time cart zoom edit close